Briggs & Stratton 30325 Manual do Operador Página 21
- Página / 30
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
21
Generator Maintenance
Generator maintenance consists of keeping the unit clean
and dry. Operate and store the unit in a clean dry
environment where it will not be exposed to excessive dust,
dirt, moisture, or any corrosive vapors. Cooling air slots in
the generator must not become clogged with snow, leaves,
or any other foreign material.
NOTE: DO NOT use water or other liquids to clean
generator. Liquids can enter engine fuel system, causing
poor performance and/or failure to occur. In addition, if
liquid enters generator through cooling air slots, some of the
liquid will be retained in voids and cracks of the rotor and
stator winding insulation. Liquid and dirt buildup on the
generator internal windings will eventually decrease the
insulation resistance of these windings.
Cleaning
Daily or before use, look around and underneath the
generator for signs of oil or fuel leaks. Clean accumulated
debris from inside and outside the generator. Keep the
linkage, spring and other engine controls clean. Keep the
area around and behind the muffler free from any
combustible debris. Inspect cooling air slots and openings
on generator. These openings must be kept clean and
unobstructed.
Engine parts should be kept clean to reduce the risk of
overheating and ignition of accumulated debris:
• Use a damp cloth to wipe exterior surfaces clean.
• Use a soft bristle brush to loosen caked on dirt or oil.
• Use a vacuum cleaner to pick up loose dirt and debris.
Battery Maintenance
Other than float charging, described elsewhere, no
maintenance is required for the starting battery. Keep the
battery and terminals clean and dry.
IMPORTANT: Battery charging should be performed in a dry
location, such as inside a garage.
Fuel Valve Maintenance
The fuel valve is equipped with a fuel sediment cup, screen,
retaining ring and o-ring that need to be cleaned every
100 hours or once a year (whichever occurs first).
1. Move fuel valve to “Off” position.
2. Remove sediment cup (A) from fuel valve. Remove
o-ring (B), retaining ring (C) and screen (D) from fuel
valve.
3. Wash sediment cup, o-ring, retaining ring, and screen
in a nonflammable solvent. Dry them thoroughly.
4. Place screen, retaining ring, and o-ring into fuel valve.
Install sediment cup and tighten securely.
5. Move fuel valve to “On” position, and check for leaks.
Replace o-ring if there is any leakage.
NOTICE
Improper treatment of generator can damage it and
shorten its life.
• DO NOT expose generator to excessive moisture, dust, dirt, or
corrosive vapors.
• DO NOT insert any objects through cooling slots.
A
B
C
D
- Operator’s Manual 1
- Table of Contents 3
- SAVE THESE INSTRUCTIONS 4
- Assembly 7
- Add Engine Oil 9
- Add Fuel 9
- System Ground 10
- Generator Location 10
- Features and Controls 11
- NEMA 14-50 13
- Battery Charger 14
- NEMA L5-20 14
- Operation 15
- Stopping the Engine 16
- Oil Pressure Shutdown 16
- Connecting Electrical Loads 16
- Charging a Battery 17
- Cold Weather Operation 17
- Don’t Overload Generator 19
- Maintenance 20
- Generator Maintenance 21
- Battery Maintenance 21
- Fuel Valve Maintenance 21
- Engine Maintenance 22
- Troubleshooting 26
- Warranties 27
- Emission Information 28
- 198189E, Rev. B, 12/31/2006 29
- *Second year parts only 29
- Portable Generator 30
Manuais e produtos relacionados com Geradores de energia Briggs & Stratton 30325
Geradores de energia Briggs & Stratton 10000 Watt Home Generator System Manual do Operador
(16 páginas)
(16 páginas)
Geradores de energia Briggs & Stratton 7000 Rated Watts Home Standby Generator Manual do Operador
(88 páginas)
(88 páginas)
(56 páginas)Silvercrest Waga podręczniki użytkownika
Zaczynanie od S
Comentários a estes Manuais